"/d 0" means destination location is disk 0 /d 0:0 means the destination location is partition 0 on disk 0 /d D means the destination location is partition D "null" means not to use "/d", and restore to the original location.Īdjust the size of the destination partition. Specify the destination location to restore to. i 0 means disk 0 or dynamic volume 0 / i 0:0 means partition 0 on disk 0 "null" means no need to specify the partition to be restored while performing system restore. Specify the source, which means the disk, partition or dynamic volume to be restored in the image file. Specify to use the latest backup version to restore(because of incremental or diferential backup).The backup version corresponding to the current image file will be restored without this "/v" command. "system" means to restore system backup "disk" means to restore disk backup "part" means to restore partition backup or dynamic volume backup. Restore the backup of a system, disk, partition or dynamic volume. (Note: there is no space between the "/l" and "0")ĪMBackup.exe /b new /t system /d "d:\sys" /e "mypassword" Command Line for Restoreįor a backup restoration, the required parameters are: Use /l to show ALL disks on this computer, /l0 or /l1 shows partitions only of disk 0 or disk 1. List disks and partitions on this computer. m 1490.īackup the disk or partition in a sector-by-sector way or not, it could be decided by one of these two parameters: 0 or 1Ġmeans standard backup, which is the default backup option.1Raw backup This will do a raw (pseudo forensic) sector-by-sector backup, e.g. This specifies the maximum size of each file e.g. Size in MB for splitting a large image file into smaller files. Password if you backup to a network and a password is required to access the network e.g. You may set up the username by using this parameter, e.g. Username if you backup to a network and the username is required to access the network. e "123" means "123" becomes the password for the image file. The compression level of the image file could be one of the following: 0, 1 or 2Ġno compression1fast standard compression2higher compression level, but takes more time to process.Įncrypt image file, e.g. The following are some optional parameters:Īssign a name for the backup to distinguish it from others This means creating an incremental or a differential backup based on image-"d:\backup\ab.adi" Specify the main file for creating incremental or differential backups from, e.g. Inccreate an incremental backup based on the last backupdifcreate a differential backup based on the last full backupfullcreate a subsequent full backup Specify the type of backup, it could be one of the following: inc, dif or full d D:\Path\Fileįor incremental and differential backup, the required parameters are: s 0:1ĭestination path for saving the backup image, e.g. s C.įor partitions without a drive letter, specify the partition number, e.g. s 0.įor a partition backup, specify the drive letter, e.g. Systemmeans to backup your systemdiskmeans to backup diskspartmeans to backup partitionsįor a disk backup specify the number of the disk, e.g. Specify the type of source, it could be one of the following: system, disk or part Specify the type of backup, it could be one of the following: new, inc, dif or full display the complete usage of the restore commandįor a new backup, the required parameters are: display the complete usage of the clone command display the complete usage of the backup command display the complete usage of the list command "AMBackup" has five functions, which are backup(/b), clone(/c), restore(/r), list(/l), and help(/?) Type “AMbackup /?” in Comand prompt to look for help This commands AMBackup.exeto start a new disk backup and backup disk 0, next save the backup file to “D:\disk backup” and name the backup file as “Backup Disk0” The options below specify all the Command line parameters that can be used to constitute a fully functional command, e.g:ĪMBackup.exe /b new /t disk /s 0 /d "d:\disk" /n "Backup Disk0" Note: the path must match the installation directory of the program you installed.ģ. This means open the path-“C:\Program Files\AOMEI Backupper” which is the installation directory of AOMEI Backupper of your version. If you installed the program in a different location, enter that location instead Navigate to the of AOMEI Backupper installation directory by typing in:Ĭd C:\Program Files\AOMEI Backupper. To open the Command prompt, either:Ī) Click Start, right click Command Prompt and select "Run as Administrator"ī) Press WIN R to open "Run" window and type "cmd" to open it.Ģ. Run the command line prompt as administrator. For more advanced use AOMEI Backupper can be controlled from the Command Line, instead of using the Windows interface.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |